The Nano and the PinPulse shield
The Nano seats in the shield, which puts a light on 22 of its pins. Power off before it goes in or comes out, and mind the direction.
See this board 16MHz ATmega328PNano V3.0 USB-C (ATmega328P)Flash: 32 KB program memory
You have this22one per I/O pinNano PinPulse Shield, 22 Pin LEDsEach pin: 3 ways outBuild it with your AI
Pick what you want to make, copy, and paste it into ChatGPT, Claude or any assistant. It carries the specs and links to the whole handbook and its own sketches, so the assistant starts from them instead of guessing.
I have a Lonely Binary Nano PinPulse Shield, 22 Pin LEDs (product code nanopinpulse). Help me with this: Help me with the handbook's example "Chase the LEDs" (https://learn.lonelybinary.com/manuals/nano/chase-the-leds): get it running on my board, and explain the wiring. Before you write any code, open these. They are the maker's reference for this exact product: - The full reference (specs, wiring, every example sketch, troubleshooting): https://learn.lonelybinary.com/ai/nanopinpulse.md - The handbook's sketch for this task: https://learn.lonelybinary.com/ai/nanopinpulse/chase_the_leds.ino Start from that sketch and change only what my task needs. Tell me the wiring, pin by pin, and the board settings. If you cannot open links, use the facts below. Do not invent pins, voltages or libraries that are not here; ask me instead. Specifications: - In the range: The Nano V3.0 with USB-C, and the PinPulse shield it seats in; the shop sells them together in a three-pack - Chip: ATmega328P at 16 MHz on a ceramic resonator; a CH340C turns the USB-C socket into a serial port - Memory: 32 KB flash, 2 KB SRAM, 1 KB EEPROM - Pins: 14 digital pins (D0 to D13, with D0 and D1 shared with the USB serial line), 6 of them with PWM (D3, D5, D6, D9, D10, D11), and 8 analogue inputs (A0 to A7, of which A6 and A7 read analogue only) - Power: 5 V from the USB-C socket through a Schottky diode, or VIN (about 7 to 12 V) through an AMS1117-5.0 regulator; the 3V3 pin comes from an ME6217C33M5G fed by the 5 V rail - Board size: 43.2 × 18 mm, two rows of 15 pins at 2.54 mm and 15.24 mm apart; the pins reach 8.4 mm below the board and the tallest part is 10.1 mm - LEDs: 22 red LEDs on the shield: TXD, RXD, D2 to D13 and A0 to A7. Each hangs off one channel of an SN74HC04 hex inverter, so the pin drives only a CMOS input (1 µA, 10 pF at most) and the light is paid for by the 5 V rail through 5.1 kΩ - Pin access: Every pin comes out 3 ways on the shield: the socket the Nano seats in, a strip of male pins and a strip of female sockets, so both kinds of jumper wire fit - Shield size: 55 × 49 mm with two 4.8 mm mounting holes 48 mm apart; the sockets stand 8.5 mm tall Questions people ask: - Which way round does the Nano go in the shield? USB-C at the end marked USB on the shield, where the arrow reads USB IS ORIENTED THIS WAY. The Nano turned through 180° still fits, and then its power pins land on signal holes and signal pins land on the shield's rails. - Can I plug the Nano into the shield while it is powered? No. Power off first, seat the Nano fully with both rows of pins home, check the direction, and only then plug the cable in. To remove it, unplug the cable first and lift the Nano out after. Plugging or unplugging with power on can leave the shield warm. - Why do some LEDs flicker when I touch the shield? A pin your sketch has not set is floating, and your body picks up mains hum that moves it between LOW and HIGH. Set the pin with pinMode and a digitalWrite, or INPUT_PULLUP, and it stops. - Why is there no LED on VIN, GND, RST, 5V, AREF and 3V3? They are rails, a reset line and a reference input, not pins that go HIGH and LOW. A light on them would show nothing useful. - What do I choose in the Arduino IDE? Board Arduino Nano and Processor ATmega328P. If an upload stops with an error that says not in sync, try Processor ATmega328P (Old Bootloader).
Product questions
See what other owners have asked, and read their solutions.
Nano PinPulse Shield, 22 Pin LEDs
Loading discussions…
Email us or reply to your order, and quote nanopinpulse — that identifies the product. If something is missing from the bag, your order is the record of what shipped.
Point a phone camera at the code and this page opens there. It is the same address as the one printed on your box, so it is also what to show someone you are passing the board to.