UNO R3/Power/05. The 5V and 3V3 pins
Power · 05 of 6

The 5V and 3V3 pins

The 5V pin is the board's own 5 V rail and the 3V3 pin is a small regulator fed from it. How much either can give depends on where the rail's power comes from: on USB the limit is a 0.5 A fuse, and on the jack it is how hot the 5 V regulator gets turning the extra volts into heat.

Two pins, one source

The 5V pin is the 5 V rail itself, so it gives whatever the rail can spare. The 3V3 pin is the output of U2, an XC6206 regulator rated at 200 mA, whose input is the same 5 V rail. Every milliamp taken from 3V3 is also a milliamp taken from 5V.

What the rail can spare depends on what is feeding it, USB or the jack, as the last article set out. The board's own parts take some first: the chip, the CH340C, the LM358 and the lamps add up to a few tens of milliamps, a figure we have not measured on this board. What is left is yours.

Never wire 5V or 3V3 to GND. It is a short circuit straight across the supply.

From USB, the fuse is the limit

On USB the rail comes through F2, a resettable fuse that holds 0.5 A. That is the most it is guaranteed to pass without tripping; somewhere above it, it heats, its resistance jumps, and the rail drops. It resets itself after the load is removed and it has cooled.

So the budget on USB is 0.5 A, less the board's own few tens of milliamps, less a margin, because a fuse running near its hold current is running warm. A few hundred milliamps for everything you add, LEDs, a sensor, a small display, is comfortable. A servo or a motor is not, because the current it takes to start moving is many times what it takes to keep moving, and that is exactly when it needs it.

From the jack, the heat is the limit

On the jack the rail comes from U1, the AMS1117-5.0. A linear regulator works by passing the whole current and dropping the difference between its input and its output across itself. That drop is heat:

heat = (VIN - 5 V) x current

The same current can be harmless or too hot to touch depending on the supply.

Where the extra volts go
9 V, 200 mA
Supply on the jack9 V
Current taken from the 5 V rail200 mA
VIN after the diode
8.6 V
Heat in U1
0.72 W
Regulator, about
90 °C
Too hot to touch, and still inside the limit. Lower the supply, or the current: at 9 V each extra 100 mA adds about 32 °C.

The maker's datasheet gives the AMS1117 in its SOT-223 package a thermal resistance of up to about 90 °C per watt, less with more copper under it: every watt of heat raises it about 90 °C above the room. This board's copper may do somewhat better or worse, so treat the figure's temperatures as about, not exact. Past 125 °C it is outside the datasheet's operating range; above about 165 °C its thermal protection switches the output off until it cools, and the board resets.

Half a watt of heat, about 45 °C above the room, is a reasonable ceiling for a part you might touch. VIN is the jack voltage less about 0.4 V for the diode, so for half a watt the whole board, its own few tens of milliamps included, can take about:

Supply in the jackVINCurrent for about 0.5 W
7 V6.6 Vabout 300 mA
9 V8.6 Vabout 140 mA
12 V11.6 Vabout 75 mA

The regulator itself is rated 1 A, and it is never the 1 A that stops it. A 12 V supply is within the recommended range and leaves the least to spare. Choose the lowest supply that is comfortably above 7 V.

The 3V3 pin

U2 drops 5 V to 3.3 V, so it heats too: 1.7 V times its current. At its full 200 mA that is 0.34 W, in a SOT-23, a package about 3 mm long that can shed only a few hundred milliwatts. Treat 200 mA as the ceiling, not the working figure, and remember it comes out of the 5 V budget above.

3V3 is for parts that need 3.3 V: most modern sensors and many small displays. A 3.3 V part's signal pins still meet the UNO's 5 V signals, so check its datasheet for whether it tolerates 5 V on its inputs before wiring it to the UNO's pins.

How to know what you have

Add up the currents of what you plan to connect, from their datasheets, before you connect them. That number against 0.5 A on USB, or against the table above on the jack, is the whole decision. For the rail voltage itself, Measure the board's own supply has the chip read its own 5 V, which is a good check that the rail holds up with the load connected.

When it does not work

The regulator next to the jack is too hot to touch

It is turning (VIN minus 5 V) times the current into heat. Use a lower supply voltage in the jack, 7 to 9 V rather than 12, or take the load's power from somewhere other than the 5V pin. On USB the regulator is not in use at all.

The board resets every time the load switches on

The load's starting current pulls the rail down far enough to reset the chip. Motors and servos are the usual cause. Give the load its own supply and join only its ground to the board's GND.

The board runs on USB but resets on the jack with the same load

On the jack, the AMS1117 is heating up until its thermal protection cuts the output. Work out (VIN minus 5) times the current: if it is much over half a watt, lower the jack voltage or move the load to its own supply.

A 3.3 V module browns out or restarts

The 3V3 pin is rated 200 mA, and parts with a radio can draw more than that in short bursts. Check the module's peak current, not its average. A module that needs more needs its own 3.3 V regulator, fed from the 5V pin or its own supply.

The fuse trips on USB with only a small load connected

Something is drawing more than you think, or there is a short. Unplug the load, let the fuse cool, and check the wiring with the USB cable out: a wire from 5V or 3V3 straight to GND trips the fuse instantly.

Where this goes next

Nine symptoms, the checks for each in order, and where the handbooks cover them.

Troubleshooting checklist →

Edit this page — content/books/uno/the-5v-and-3v3-pins.mdx

Community

Questions about this product

See what other owners have asked, and read their solutions.

Ask a question ↗

UNO R3 USB-C (ATmega328P)

Loading discussions…

Discuss this article

Ask about this page. The answer stays here, on the page it belongs to, for whoever hits the same wall next.

Browse Modules and blocks on the forum →