The ESP32-C3 OLED pluggable terminal base seen from above at an angle: a black board with a tall grey eight-way push-in terminal block down each long edge, numbers 3 to 10 printed beside the left one, two black sockets in the middle for the OLED board with a white battery connector between them, and a slide switch with two mounting holes beside it at the far edge.
VR

View it in VR

This board opens in a VR headset: life-size, or big enough to stand beside, with every pin and every part named where it sits. Open this address in the browser on a headset such as Apple Vision Pro or Meta Quest.

learn.lonelybinary.com/vr/c3plug
You have this

ESP32-C3 OLED Pluggable Terminal Base

A 25 × 20.5 mm ESP32-C3 board with a 72 × 40 OLED already wired to GPIO 5 and 6, and three bases it seats on, each with a battery connector, charger and switch: 2.54 mm pins, push-in terminals or screw terminals.

Terminals
2 × 8at 3.5 mm
Base size
53.1 × 32.5mm
Height
14.9mm
Mounting holes
16mm apart

Turn it over, click any terminal, and see which GPIO it is and what the ESP32-C3 OLED board already uses it for.

Product questions & answers ↓

The ESP32-C3 OLED and its three bases

One ESP32-C3 OLED board, three bases it seats on: 2.54 mm pins, push-in terminals or screw terminals. Each base carries the same battery connector, charger and power switch.

Build it with your AI

Pick what you want to make, copy, and paste it into ChatGPT, Claude or any assistant. It carries the specs and links to the whole handbook and its own sketches, so the assistant starts from them instead of guessing.

I have a Lonely Binary ESP32-C3 OLED Pluggable Terminal Base (product code c3plug). Help me with this:

Help me with the handbook's example "Arduino IDE, set up for this board" (https://learn.lonelybinary.com/manuals/c3oled/arduino-ide-setup): get it running on my board, and explain the wiring.

Before you write any code, open these. They are the maker's reference for this exact product:
- The full reference (specs, wiring, every example sketch, troubleshooting): https://learn.lonelybinary.com/ai/c3plug.md
- The handbook's sketch for this task: https://learn.lonelybinary.com/ai/c3plug/hello_c3.ino

Start from that sketch and change only what my task needs. Tell me the wiring, pin by pin, and the board settings.
If you cannot open links, use the facts below. Do not invent pins, voltages or libraries that are not here; ask me instead.

Specifications:
- In the range: The ESP32-C3 OLED board, and three bases it seats on: expansion (2.54 mm pins and sockets), pluggable terminal (3.5 mm push-in) and screw terminal (3.5 mm screw)
- Chip: ESP32-C3FH4, single-core RISC-V up to 160 MHz, 4 MB flash inside the module, 400 kB SRAM, no PSRAM; Wi-Fi 4 and Bluetooth LE; the USB-C socket goes straight to the chip, so there is no driver to install
- Display: 0.42 in OLED, 72 × 40 pixels, SH1106 at I²C address 0x3C, on GPIO 5 (SDA) and GPIO 6 (SCL)
- Holes: 16 on the board and on every base: GPIO 3, 4, 5, 6, 7, 8, 9 and 10 down one side, and GPIO 0, 1, 2, TX (21), RX (20), 3.3 V, ground and 5 V down the other. Six are answering to something before your sketch runs: 5 and 6 (display), 8 (blue LED), 9 (BOO button), 20 and 21 (serial)
- Board size: 25 × 20.5 mm, the two rows of holes 17.78 mm apart
- Edge connectors: Expansion: 8 pins and 8 sockets a side at 2.54 mm, wired together. Pluggable: 2 × 8 push-in terminals at 3.5 mm. Screw: 2 × 8 screw terminals at 3.5 mm
- Base size: Expansion 39.5 × 32.5 mm, screw terminal 44.5 × 32.5 mm, pluggable terminal 53.1 × 32.5 mm
- Tallest part: Measured from the underside of the base: expansion 10.1 mm, screw terminal 10.3 mm, pluggable terminal 14.9 mm
- Mounting: Two 4.8 mm holes, 16 mm apart, on each base
- Battery: JST PH 2.0 two-pin socket for a single 3.7 V lithium cell with a protection circuit; TP4054 linear charger, which takes the cell to 4.2 V; a slide switch between cell and board
- Battery monitor: An open solder jumper marked BATTERY MONITOR and IO2 joins two 100 kΩ resistors across the cell, halved, to GPIO 2. It ships open

Questions people ask:
- Which way round does the board go on a base? Antenna at the power-switch end, USB-C at the battery-connector end. The check that needs no memory: find V5 on the board and 5V on the base and put them at the same end. The board fits turned around just as firmly, and that way the base's 5 V pad meets the pin marked 3, so the battery rail drives three chip pins.
- Which base should I buy? Jumper wires and breadboards: the expansion base, which is also the smallest. Bare wire you change often: the pluggable terminal base, push-in with no screwdriver. Bare wire that has to stay put: the screw terminal base. All three bring out the same sixteen holes and carry the same battery circuit.
- Does a sketch need changing between bases? No. The GPIO numbers belong to the board, and every base brings out the same sixteen holes, so a sketch is the same on all three.
- Why does the base's charge LED not light when I plug in USB? The switch has to be ON, with a battery connected. With the switch OFF the cell is out of the charging circuit, and the charge LED can flicker so fast it looks half-lit. The cell is not charging in that state.
- Why is GPIO 2 not free when I use the battery level? The BATTERY MONITOR jumper connects the divider across the cell to GPIO 2. It ships open so the divider does not draw from the cell; bridge it only if you will read the level, and GPIO 2 is spent from then on.
- Why does the board fail to join my Wi-Fi? The antenna is a ceramic chip a few millimetres long, and at full transmit power the radio overdrives it. The back of every base prints WIFI_POWER_15DBM to 8_5DBM: setting the power down to 8.5 dBm in the sketch is what makes the board stay on a network.
- Do I need a driver? No. The C3 has its own USB peripheral, so the board appears as a serial port with nothing to install. Set USB CDC On Boot to Enabled in the Arduino IDE, or the sketch runs and prints nothing.
Community

Product questions

See what other owners have asked, and read their solutions.

Ask a question ↗

ESP32-C3 OLED Pluggable Terminal Base

Loading discussions…

Need another
ESP32-C3 OLED Pluggable Terminal Base
Order or missing parts?

Email us or reply to your order, and quote c3plug — that identifies the product. If something is missing from the bag, your order is the record of what shipped.

Take it with you

Point a phone camera at the code and this page opens there. It is the same address as the one printed on your box, so it is also what to show someone you are passing the board to.