Topics/Power/USB-C PD Trigger, 100 W Decoy 5–20 V
POWERUSBbeginner

USB-C PD Trigger, 100 W Decoy 5–20 V

A USB-C charger holds 9, 12, 15 and 20 V and hands you 5 V until something asks. This board asks. Three levers set the voltage, a CH224K does the negotiating, and two pairs of holes bring it out.

USB-C PD Trigger, 100 W Decoy 5–20 V, 12-Pack

Specifications

In the box12 bare trigger boards, output holes empty, plus 2 × 40-pin straight and 2 × 40-pin right-angle breakaway male header strips. 160 header pins against the 24 that twelve boards can take
VoltagesFixed 5, 9, 12, 15 or 20 V, selected by a three-position DIP switch. Which one you get also depends on the charger offering it
ChipWCH CH224K, a USB Power Delivery 3.0 sink controller in a ten-pin ESSOP package on the underside. I/O level configuration, no firmware and nothing to program
Ceiling100 W, which is 20 V at 5 A. It needs a 100 W charger and an electronically marked cable; an ordinary cable is limited to 3 A, so 20 V tops out at 60 W
Setting the voltageLevers 1, 2 and 3 drive CFG1, CFG2 and CFG3. The bar behind them prints 0 at one end and 1 at the other: 5 V is 1XX, 9 V is 000, 12 V is 001, 15 V is 011 and 20 V is 010. The same table is on the back of the board
OutputVCC and GND, brought out twice on the same copper, as four empty holes: a 3.5 mm pair (1.1 mm holes, the footprint of a terminal block) and a 2.54 mm pair (1.0 mm holes, for the header pins in the box) 1.8 mm behind it. GND is the pair nearer the top edge
Power LEDRed, through 5.1 kΩ from the chip's own 3.3 V rail. About 0.3 mA. It proves the board has VBUS, and says nothing about whether the negotiation succeeded
ProtectionThe chip has over-voltage and over-temperature protection for itself, with the over-temperature threshold around 105 °C. There is no fuse, no polyfuse and no TVS on the board — a fault downstream sees whatever the charger will deliver
Board26.0 × 11.3 mm and 1.6 mm thick, revision V1.2. The USB-C socket overhangs the edge by about 0.8 mm

What it does

A modern USB-C charger contains four or five separate voltage rails and hands you the lowest one. It stays at 5 V until something on the other end of the cable asks for more, in a protocol called USB Power Delivery, over a wire called CC.

This board does the asking. A CH224K sink controller reads three switch levers, requests the matching voltage, and holds it at two output holes — turning a laptop charger into a fixed 5, 9, 12, 15 or 20 V supply for whatever you are building.

Drag to turn it
The trigger board as it ships, output holes empty. Turn it over for the chip and the voltage table.

Setting the voltage

The three levers drive the chip's CFG1, CFG2 and CFG3 pins. The bar printed behind them says 0 at one end and 1 at the other, and the same table is on the underside of every board:

VoltageLever 1Lever 2Lever 3
5 V1XX
9 V000
12 V001
15 V011
20 V010

X means the chip stops reading that lever. All eight patterns are valid, so there is no combination to avoid — only the wrong voltage for your load.

Wiring it

  1. Set the levers for the voltage you want, with the corner of a small screwdriver.
  2. Plug a USB-C cable from a Power Delivery charger into the socket.
  3. Meter across the output holes — VCC is the lower pair, GND the upper — and wait two seconds for the negotiation.
  4. Unplug, solder your load's wires (or header pins) to VCC and GND, and plug back in.

Where to start

The handbook below takes it from the beginning: why a charger holds back its higher voltages, what is on the board, how the levers become a number, and what decides whether you get the voltage you asked for. If you are only here for the switch table, the three switches is the page you want.

When it doesn’t work

I set it to 20 V and I am still getting 5 V. Is the board faulty?
Almost never. Either the levers are not what you think — 20 V is 0 1 0, and 15 V is 0 1 1, so the two differ by lever 3 rather than lever 2 — or the charger has no 20 V rail to give. Read the levers against the table on the back of the board, then read the voltage list printed on the charger's case. A third possibility is a charge-only cable with no CC conductor, which stops the negotiation happening at all.
Does ON mean on?
The board does not label the levers ON and OFF. The white bar behind them prints 0 at one end and 1 at the other, and those are the digits the table uses. Pushing a lever to the 0 end — which is the end the switch body marks ON — ties that configuration pin to ground, and the chip reads it as 0.
Why does it say 100 W when I only get 60 W?
100 W is 20 V × 5 A, and 5 A over USB-C needs a cable with an e-marker chip in it. Without one, the specification limits the cable to 3 A, so 20 V gives 60 W. You also need a charger that is actually a 100 W charger: a 65 W brick at 20 V is offering 3.25 A whatever the cable does.
Is there a screw terminal, and can I use it with the breadboard pins?
The board is bare: there is no terminal block in the box. The larger pair of holes is the footprint for one at 3.5 mm pitch, and the smaller pair takes the header pins that are in the box. They are the same two nets on one piece of copper, 1.8 mm apart, and a terminal block's body would sit over the header holes, so fit one or the other. Wire soldered straight into either pair also works.
Is there any protection if my circuit shorts?
Not on this board. The chip protects itself against over-voltage and over-temperature, and the charger has its own current limit, but between them there is nothing — no fuse, no polyfuse, no TVS. Whatever a 65 W charger is prepared to deliver into a fault will go straight through the output holes. Put the protection on your side of it.
Can I change the voltage while it is running?
The chip's datasheet lists dynamic adjustment of the requested voltage among the family's features, so moving a lever will generally make it ask again. It is still a bad habit with a load connected: a lever crossing over passes through states you did not intend, and your load sees all of them. Set the levers, plug in, meter, then connect the load.
Does it do PPS or the higher EPR voltages?
No. The CH224K is a Power Delivery 3.0 part configured by pin levels, and what it can request is the five fixed voltages in the table. Programmable supply, adjustable voltage and the 28 V EPR range belong to other chips in the same family, which this board does not have.
What does the LED tell me?
That the board has VBUS. It runs from the chip's internal 3.3 V rail, which comes up on the 5 V that every USB-C source provides before anything is negotiated, so it lights just the same when a request has been refused. The only honest indicator is a meter across the VCC and GND holes.

The PD trigger handbook

11 articles · about 45 minutes

This page is the reference: what the part is, what it is made of, and the questions people arrive already asking. The handbook is the walk — the same part in the order somebody actually meets it.

Why a trigger board

2 articles

A charger with 20 V inside it that will only hand you 5 V, and the bag of twelve boards that changes its mind.

The board in your hand

3 articles

Six parts, two ways out of the same two holes, and one LED that tells you less than you think.

Setting the voltage

3 articles

Three levers, a table printed on the back of the board, and why the thing they print is 0 and 1 rather than on and off.

What you actually get

3 articles

The charger has to own the voltage, the cable has to carry the current, and neither of them is on this board.

Edit this page — content/modules/pdtrig.mdx

Community

Questions about this product

See what other owners have asked, and read their solutions.

Ask a question ↗

USB-C PD Trigger, 100 W Decoy 5–20 V, 12-Pack

Loading discussions…

Discuss this article

Ask about this page. The answer stays here, on the page it belongs to, for whoever hits the same wall next.

Browse Modules and blocks on the forum →