Topics/Fundamentals/TinkerBlock UNO R3 Starter Kit: the Shield and 18 Labs with 12 Modules
DIGITALANALOGPWMI2Cbeginner

TinkerBlock UNO R3 Starter Kit: the Shield and 18 Labs with 12 Modules

An UNO R3, the TinkerBlock shield and twelve plug-in modules, with no breadboard and no soldering. The handbook covers the shield, which socket reaches which pin, and 18 labs that put the modules together: a Morse key, a melody player, police lights, a clap alarm and an invisible beam alarm.

TinkerBlock UNO R3 Starter Kit, 12 Modules

Specifications

In the kit1 UNO R3 (ATmega328P, USB-C), 1 TinkerBlock UNO shield, 12 TinkerBlock modules and the cables that join them
Modules10 mm XL LED, push button, disc potentiometer, ambient light sensor, NTC thermistor, WS2812 RGB LED bar, active buzzer, passive buzzer, analog microphone, reflective optical sensor, IR transmitter and IR receiver
Shield12 four-pin sockets (GND, 5V and two UNO pins each, 2.0 mm pitch), plus three six-pin and two eight-pin sockets for SPI, PWM and analogue
One ruleA module carries its signal on the socket's fourth pin, so a module in the D2/D3 socket is on D3, and the socket labelled A2/A3 puts it on A3
I2CFour sockets on A4 (SDA) and A5 (SCL), pulled up to 5 V through 4.7 kΩ on the shield
PowerThe sockets' 5 V comes from the UNO through a resettable fuse of about 1 A; the PWR lamp shows it is there
Logic5 V, the UNO's. Every module in the kit runs on it

Unplug the USB cable before you move a module to another socket. Every socket carries 5 V, and a plug that goes in at an angle can touch the wrong pins first.

What it is

An UNO R3, a shield that sits on top of it, and twelve TinkerBlock modules. The shield turns the UNO's header strips into sockets: each module plugs into one with a single cable, so a build is a few cables and a sketch.

Drag to turn it
The shield. The header strips underneath plug straight into the UNO's sockets; every white socket on top takes one TinkerBlock cable. Turn it over for the back.

What is where

This handbook covers what only the kit has: the shield, and 18 labs that put the modules together. Everything else already has a page of its own.

You wantIt is in
The board: its parts, power and pinsThe UNO R3 handbook
The Arduino IDE, the language, digital and analogue pins, PWMThe ATmega328P book
One module on its own: its circuit and its first sketchIts page under TinkerBlock
The shield, and builds that use several modulesThis handbook

Where to start

What is in the box, then the shield, then the first lab.

When it doesn’t work

Do I need a breadboard or a soldering iron?
No. The shield sits on the UNO, and each module joins the shield with one cable. Nothing in the 18 labs needs another part.
Which socket do I plug a module into?
Each lab names its socket. The rule behind it: a module's signal is the socket's fourth pin, so it is on the second of the two pins printed beside that socket. The D2/D3 socket puts a module on D3.
Where are the basics of each module?
Each module has its own page under the TinkerBlock section, with its first sketch and what to check when it misbehaves. The labs here link to it rather than repeating it.
Where do I learn the Arduino IDE and the language?
In the ATmega328P book, shared with the UNO's own handbook: installing the IDE and the CH340 driver, setup() and loop(), variables, millis(), libraries, digital and analogue pins and PWM.

The TinkerBlock UNO kit handbook

21 articles · about 115 minutes

This page is the reference: what the part is, what it is made of, and the questions people arrive already asking. The handbook is the walk — the same part in the order somebody actually meets it.

The kit

2 articles

What is in the box, and the shield: which socket is which pin, the pull-ups, the fuse and the reset button.

Lights and buttons

4 articles

The XL LED and the push button: a blink, a counter, a long press and a double click.

A knob, light and heat

3 articles

Three analogue modules: a knob that dims the LED, a night light, and a temperature alarm.

Colour

3 articles

The WS2812 bar: the first library, police lights, and a button that throws colours.

Sound

4 articles

The two buzzers: Morse code, a melody player, a player you drive from the Serial Monitor, and a light-and-music show.

Hands, sound and beams

4 articles

The reflective sensor, the microphone and the infrared pair: a wave switch, a clap alarm, disco lights and a beam alarm.

When it does not work

1 article

A checklist for the kit: the cable, the socket, the PWR lamp and the pin the sketch names.

Edit this page — content/modules/tkbu.mdx

Community

Questions about this product

See what other owners have asked, and read their solutions.

Ask a question ↗

TinkerBlock UNO R3 Starter Kit, 12 Modules

Loading discussions…

Discuss this article

Ask about this page. The answer stays here, on the page it belongs to, for whoever hits the same wall next.

Browse Modules and blocks on the forum →