The ESP32-S3 pluggable terminal base seen from above at an angle: a black board with four corner mounting holes, two tall black sockets down the middle for the ESP32-S3, a white twelve-way push-in terminal block and a short four-way power block along each long edge, and a white fifteen-way ribbon socket at the far end.
VR

View it in VR

This board opens in a VR headset: life-size, or big enough to stand beside, with every pin and every part named where it sits. Open this address in the browser on a headset such as Apple Vision Pro or Meta Quest.

learn.lonelybinary.com/vr/s3plug
You have this

ESP32-S3 Pluggable Terminal Base

Four bases for the 44-pin Lonely Binary ESP32-S3. Which GPIOs each one brings out, which way round the board goes, the fifteen-way display plug they all share on the same GPIOs, and the 36 LEDs on the PinPulse that cannot disturb I²C or SPI.

GPIOs out
24
Terminals
2 × 12at 3.5 mm
Display port
15way FPC

Turn it over, click any terminal, and see which GPIO it is and what the ESP32-S3 can do with it.

Product questions & answers ↓

The four ESP32-S3 bases

One ESP32-S3, one display plug on the same GPIOs, four ways to wire to it: pins, push-in terminals, screw terminals, or pins with an LED on every GPIO.

Questions people ask first

  • Which way round does the ESP32-S3 go on the base?

    Its USB sockets go over the two boxes printed USB, at the bottom of the base, with the antenna end at the top under the display connector.

    Nothing stops the other way: the two sockets are identical, so the board seats just as firmly end for end. Put in backwards, its 3.3 V regulator output ends up wired to ground, and the board can be damaged for good. Seat the board first and plug the USB cable in second, every time.

  • Where does the power for my sensors come from?

    The base has no regulator, no battery connector and no power input. It is powered through the ESP32-S3's own USB sockets, and every power way on it is one of that board's pins carried out.

    The 3V3 ways are the output of the regulator on the ESP32-S3. The 5V ways are the board's 5V pin: about 4.6 V with a USB cable plugged in, and nothing without one. Nothing on the way is switched, fused or filtered.

  • Can I run a motor, relay or LED strip from the base?

    Not from its power ways. Motors, relays, servos and long LED strips need their own supply, with its ground joined to a GND way on the base, because the ESP32-S3's regulator is small and is also running your sketch.

    Small sensors and a display can take 3V3 and ground from the base. No current rating is quoted for the ways, because none has been checked.

  • How many GPIOs does the Pluggable Terminal Base bring out?

    24 of the ESP32-S3 Gold's 36 GPIOs, once each, on two 12-way push-in blocks, plus two 4-way power blocks.

    Twelve do not come out: 0, 1, 2, 3, 4, 35, 36, 37, 43, 44, 45 and 46, and the RST pin. GPIO 1, 2 and 4 reach the display connector and nothing else. All of the I²C and SPI pins are on the left block, and GPIO 19 and 20 (the native USB pair, on the right block) should be left alone while a sketch is using USB.

  • My sensor resets when Wi-Fi connects. Why?

    The ESP32-S3's datasheet gives about 340 mA at the peak while Wi-Fi transmits, and a USB port is meant to supply 500 mA in all. The burst lasts a moment and the 3.3 V rail dips with it; a sensor that resets when Wi-Fi connects is usually seeing that dip.

    Put a capacitor of about 100 uF between 3V3 and ground, close to the sensor. It holds the rail up for the length of the burst. The base has none of its own, because it has no power parts at all.

Community

Product questions

See what other owners have asked, and read their solutions.

Ask a question ↗

ESP32-S3 Pluggable Terminal Base

Loading discussions…

Need another
ESP32-S3 Pluggable Terminal Base
Order or missing parts?

Email us or reply to your order, and quote s3plug — that identifies the product. If something is missing from the bag, your order is the record of what shipped.

Take it with you

Point a phone camera at the code and this page opens there. It is the same address as the one printed on your box, so it is also what to show someone you are passing the board to.